Source

We've unearthed this article involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround directly below on the internet and think it made sense to relate it with you here.

Installing a bath tub isn't precisely brain surgery, however it does call for solid plumbing, woodworking, and also often, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably hard job. If the old bathtub is easily accessible, the job can move immediately; if you have to open up a wall to eliminate the old bathtub as well as place the new tub, the job is much harder. In either situation, the project is within a home handyman's abilities, although you will certainly need an assistant to move out the old tub as well as set in the new one. Ensure you have actually qualified yourself for the task and also are comfortable attempting it. As opposed to hiring a service provider to take over a halfway-completed task, it is better to consider utilizing one prior to you start. Chances are you may need a professional plumber to make tube links.
This article will assist you mount a new bathtub in your shower room if you have actually currently bought a new tub as well as do not require to transform the setup of your previous water pipelines.
Your tools and product checklist ought to make up the following:

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipe Caps


 

Removing Old Taps

If you need to replace old taps with new ones as a part of your setup, after that the first thing you must do is separate the water. After doing so, activate the faucets to drain pipes any kind of water staying in the system. The process of eliminating the existing taps can be rather troublesome because of the restricted gain access to that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have been removed, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning during this process. Once the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any kind of old securing substance.
Before moving on to fit the new faucets, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.

Fitting New Touches

If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the tap and also the other end provides a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly require lowering couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin making sure that the washing machines are in place in between the tap as well as the sink. Secure the faucet in place with the maker provided backnut. Once the faucet is securely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with typical faucet ports. The former kind should be linked to the tap ends initially, tightening just by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.

Mounting the Bathtub

Making use of both wooden boards under its feet, put the bath tub in the required setting. The wood boards are valuable in equally spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto four little factors.
The next objective is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bathtub up until the level reviews level.
To set up faucets, fit the bottom of the outermost flexible tap port to the proper supply pipeline by making a compression join; then do the exact same for the various other tap.
Switch on the water system and also check all joints and new pipework for leakages and also tighten them if necessary. Fill the tub and likewise examine the overflow outlet as well as the typical electrical outlet for leaks.
Lastly, deal with the bathroom paneling as described in the producer's user's manual. Tiling and also sealing around the tub must wait till the bathtub has actually been used a minimum of when as this will certainly settle it into its final setting.

Planning for the Installment

Firstly, the supporting framework provided with the bathroom needs to be fitted (if called for) according to the manufacturer's directions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is essential to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets unit to prevent strain on the bathtub.
Fit the flexible tap ports to the bottom of the two taps using 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you use all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be suited its last setting.

Tiling Around the Tub

In the area where the bathroom fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to crack a rigid seal, creating the water to pass through the wall in between the bathroom as well as the tiling, leading to difficulties with wetness as well as possible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of soaked paper or soft rope. Keep in mind to always load the tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealant can crack rather very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently available on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or water resistant adhesive as well as grout.

Bathtub Installation

How Important Is A Bathtub To Your Home?

High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.

Install Piping Before Tub

You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.

Position the Tub

Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.

 

NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.

Assemble Drain Connections

Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.

Place a Pipe For the Shower Head

First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.

Attaching Hot and Cold Water Lines

Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.

Install the Spout

Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.

 

NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.

Check For Leaks

Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.

estore the Bathroom Wall

Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/

I'm just very curious about How to Install a Bathtub and I'm hoping you appreciated our blog posting. Do you know about someone else who is intrigued by How to Install a Bathtub Yourself? Why not promote it. Many thanks for taking the time to read it.

Hire A Pro